Vinyl Plank Flooring in an RV

Installing beautiful but easy to care for Lifeproof luxury vinyl plank flooring in an RV or cargo trailer conversion.

When we were building our cargo trailer conversion we had so many big design decisions to make. One of the biggest decision in the early stages was installing the vinyl flooring.

We went back and forth trying to decide if we should just paint the floor and call it done or install vinyl plank flooring.

Once we started researching though, it didn’t take us long to decide that vinyl flooring was the right decision for our project.

This project was another first for us. We did install a laminate plank floor in our Georgia home years ago, but we’ve never had, or installed, a vinyl plank floor.

This is for our RV though, and the biggest concern when doing anything in an RV is weight. How much weight you add to a camper is always a huge concern.

In short…weight is not your friend when it comes to an RV.

Yes, we could have just painted the floors and not added any weight but we went with the next best thing…vinyl floor planks.  

I would have never guessed that I would go for vinyl planks but they turned out to be the perfect choice for us.

They are lightweight, good looking, easy to care for and easy to install. All you need is your flooring, a mallet and a knife or saw to cut your planks.

There’s no underlayment needed for the kind of flooring we chose, so that was an added bonus. We were able to install the planks right on top of our clean plywood floors.

So, what kind of vinyl flooring were we looking for?

• It had to be durable and lightweight.
• It had to be waterproof, which meant that it couldn’t have any wood in it.
• Of course my biggest concern was looks. It had to look like wood (or as close as possible).

The flooring we ended up picking out and installing ticked all of our boxes…LifeProof vinyl plank flooring.

Choosing a color was tough one though, but I eventually settled on a warm oak color.

I wanted to warm up the white ceiling and walls but I didn’t want anything that was too busy in our 112 square foot space.

Actually, we only covered about 70 square feet, choosing to paint the wood floor under the king size bed.

It’s just a storage area anyway, and would get beat up with tools and camping equipment. Spending money on new flooring for that area didn’t make sense.

A little disclaimer here. Well, maybe a big disclaimer. 

We found out, after we installed our vinyl plank flooring, that the manufacturer does not recommend it for an RV.

The reason is because of  temperature fluctuations (particularly cold temps) and the expansion and contraction of the planks. It’s one of those cases of not reading the directions thoroughly before you install. OOPs!

We talked to a salesman at the home improvement store who sold the flooring and he never mentioned a problem putting it in an RV so we figured we were good.

Still, it was our mistake not to read the instructions thoroughly. We think that we’ll be ok because it’s such a small area that we covered, but you never know. I’ll keep you posted. 

Ok, we found our flooring now let’s get the skinny on installing it.

Tools needed to install luxury vinyl plank flooring on plywood:

As an Amazon Associate and member of other affiliate programs, I earn from qualifying purchases.

• Life Proof Vinyl Plank Flooring
• rubber mallet
• hammer
• tape measure
• straight edge
• utility knife or table saw (we used a table saw to cut our planks)

How do you install vinyl planks in a camper

Installing the vinyl flooring was pretty easy but we did have to do some prep work before we could lay the first plank.

The prep is actually the most important part of this project, which means you need to work out all of your measurements and seam placements first.

The first thing you need to measure your room and figure out which corner you will start laying your planks.

We also laid out a few planks and moved them around to check our long seam placement. You want to be sure that you know where the long seams will be so that it all looks symmetrical when it’s done.

If you just lay a long plank without knowing your seam placement, it’s possible that you may end up with a narrow row of planks when you get to the other side of the room.

Not a good look.

This is why you need to plan ahead. After you measure it all out, you may end up needing to cut the width of the planks on both sides of your room so the placement looks symmetrical. 

We didn’t have to worry about one side being off in our RV because the cabinets and bathroom will hide most of the flooring.

You won’t really see it if it’s off.

Once you figure out the width and the long seams, you need to figure out the short side seams.

You want to make sure that the last piece of the first row doesn’t have a seam less than 6 inches from the end.

The reason why is because, if the seam is too close to the end, the planks may not snap together correctly.

If it seems like you are going to end up with a seam close to the end, you may need to trim the first piece in that row to offset that short seam.

The first row is the toughest but once you get that set, you can continue installing the rest of the floor.

You just want to make sure that your short seams are staggered, and no two short seams should be within 6 inches of each other.

The vinyl planks we picked out had a tongue and groove construction. To interlock them we just had to put the tongue from one plank into the groove of another plank and snap them together.

After you snap the planks together, you may have a slight gap. We used a scrap piece of flooring and a hammer to gently tap the planks together.

We also used a rubber mallet on the seams to make sure they were snug and in place. Just remember to use a piece of wood or scrap piece of floor when you use a hammer or mallet.

We never used those tools directly on our floor.

As we got to each end, we left a 1/4 inch gap for expansion, as per the instructions.

The prep work was behind us and we were on a roll installing the floor.

Unfortunately, about half way through, we were halted by a box of damaged planks.

We ended up waiting two weeks for a new box to arrive before we could finish our floor. Not what you want to see when you’re trying to schedule your projects.

The moral of this story? Check all of your vinyl planks as soon as you get it, and before you start installing it.

Once our new planks arrived, we could continue the installation.

To finish off the floor, I ordered a couple pieces of quarter round in the same color as the floor. Although I would love to see it completely done, we haven’t installed ours yet.

We’re still in the middle of building our cabinets so the molding will be one of the last things we do.

That’s it. Our new vinyl plank floor is done and I really love how it looks.

I picked a floor that has grooves in it, as opposed to a flat surface, just to give it a little dimension and more of a realistic look.

It looks great and it’s so easy to clean. All I need to do is sweep it with a broom.

I think it’s the perfect choice for our new cargo trailer conversion.

Check out more of our cargo trailer conversion DIY projects

• RV Kitchen Backsplash

• DIY RV Privacy Curtain

• DIY Upholstered Storage Ottomans

• RV DIY Wood Shower Mat